Product Name: ZHX-340 enameled wire paint scraper
Model: ZHX-340 enameled wire paint scraper
Inquiry: 0757-26397858 Mr. Huang 13620805836
ZHX-340 enameled wire paint scraper

I. Performance:
ModelZHX-340High-performance enameled wire stripping machine, adopting the newly designed extra-hard material high-speed paint stripping cutter head, can completely remove any hard insulating paint on the wire surface, such as enamel paint,ML, Isonel, etc., without damaging the copper wire itself. Especially suitable for situations where stripping is required to the bottom of the coil, easy to operate with excellent results, modelZHX-340The enameled wire stripping machine is equipped with a stripping length termination device, which can accurately control the stripping length of the enameled wire. Without serious pollution and harm, the stripping work is fast and safe.
II. Specifications and Data:
Applicable wire diameter | Voltage | Frequency | Power | Speed | Weight |
0.35-4.5m m | 220 v | 50 Hz | 120 W | 2800r/min | 6.8kg |
III. Operation Method:
According to the cutter head specifications in the attached table, select a suitable cutter head and install it on the chuck at the front of the machine. Insert an enameled wire in the middle of the cutter head, use a fixed wrench to adjust the chuck so that the cutter head gently clamps the enameled wire, then withdraw the enameled wire. After activating the switch, hold the coil part by hand and gently push the enameled wire into the high-speed rotating cutter head until the preset stripping length is reached, then carefully withdraw the enameled wire, and the stripping work is completed. If necessary, the caliber of the cutter head can be adjusted by loosening and tightening the chuck to control the ideal stripping effect, because when the machine is running and the cutter head rotates at high speed, the insulating paint or oxide on the enameled wire is scraped off, and the surface of the copper wire after stripping is bright and clean. To set the required stripping length, loosen the fixing screw of the chuck, after withdrawing the chuck, you can see the limit thimble for the stripping length. Adjust the limit thimble through the fixing screw to set and control the stripping length of the enameled wire.
Attached Table:
Cylindrical R (flat head) Model | Applicable wire diameter | Taper R (flat head) Model | Applicable wire diameter |
*0# | 0.28mm---------0.50mm | *0# | 0.28mm---------0.50mm |
1# | 0.51mm---------0.90mm | 1# | 0.51mm---------0.90mm |
2# | 0.90mm---------1.30mm | 2# | 0.90mm---------1.30mm |
3# | 1.30mm---------1.60mm | 3# | 1.30mm---------1.60mm |
4# | 1.60mm---------1.90mm | 4# | 1.60mm---------1.90mm |
*5# | 1.90mm---------2.30mm | *5# | 1.90mm---------2.30mm |
*6# | 2.30mm---------2.60mm | *6# | 2.30mm---------2.60mm |
*7# | 2.60mm---------3.00mm | *7# | 2.60mm---------3.00mm |
*8# | 3.00mm---------3.35mm | *8# | 3.00mm---------3.35mm |
*9# | 3.35mm---------3.60mm | *9# | 3.35mm---------3.60mm |
*10# | 3.60mm---------4.00mm | *10# | 0mm---------0mm |
*11# | 4.00mm---------4.50mm | *11# | 0mm---------0mm |
*12# | 4.50mm---------5.00mm | *12# | 0mm---------0mm |
*13# | 5.00mm---------5.50mm | *13# | 0mm---------0mm |
*14# | 5.50mm---------6.00mm | *14# | 0mm---------0mm |
*15# | 6.00mm---------6.50mm | *15# | 0mm---------0mm |